收藏本站
SQE48T40025 DC-DC Converter Data Sheet
36-75 VDC Input; 2.5 VDC @ 40A Output
Operations
Input and Output Impedance
These power converters have been designed to be
stable with no external capacitors when used in low
inductance input and output circuits.
However, in some applications, the inductance
associated with the distribution from the power
source to the input of the converter can affect the
stability of the converter. A 33 μF electrolytic
capacitor with an ESR < 1 ? across the input is
required to ensure proper operation of the converter
over wide range of input source impedance and
to the ON/OFF input, in which case it must be
capable of sourcing or sinking up to 1 mA depending
on the signal polarity. See the Startup Information
section for system timing waveforms associated with
use of the ON/OFF pin.
Remote Sense (Pins 5 and 7)
The remote sense feature of the converter
compensates for voltage drops occurring between
the output pins of the converter and the load. The
SENSE(-) (Pin 5) and SENSE(+) (Pin 7) pins should
be connected at the load or at the point where
regulation is required (see Fig. B).
transients.
Vin (+)
SQE48 Converter
Vout (+)
Rw
In many applications, the user has to use decoupling
capacitance at the load. The power converter will
exhibit stable operation with external load
capacitance up to 10,000 μF.
ON/OFF (Pin 2)
Vin
ON/OFF
Vin (-)
(Top View)
100
SENSE (+)
TRIM
SENSE (-)
10
Vout (-)
Rw
Rload
The ON/OFF pin is used to turn the power converter
on or off remotely via a system signal. There are two
remote control options available, positive and
negative logic, with both referenced to Vin(-). A
typical connection is shown in Fig. A.
Fig. B: Remote sense circuit configuration.
CAUTION
If remote sensing is not utilized, the SENSE(-) pin must be
connected to the Vout(-) pin (Pin 4), and the SENSE(+) pin
must be connected to the Vout(+) pin (Pin 8) to ensure the
converter will regulate at the specified output voltage. If these
Vin (+)
SQE48 Converter
(Top View)
Vout (+)
SENSE (+)
connections are not made, the converter will deliver an
output voltage that is higher than the specified data sheet
value.
Vin
ON/OFF
TRIM
Rload
Because the sense leads carry minimal current,
SENSE (-)
large traces on the end-user board are not required.
CONTROL
INPUT
Vin (-)
Vout (-)
However, sense traces should be run side by side
and located close to a ground plane to minimize
system noise and ensure optimum performance.
Fig. A: Circuit configuration for ON/OFF function.
The positive logic version turns on when the ON/OFF
pin is at a logic high and turns off when the pin is at a
logic low. The converter is on when the ON/OFF pin
is left open. See the Electrical Specifications for logic
high/low definitions.
The negative logic version turns on when the pin is
at a logic low and turns off when the pin is at a logic
high. The ON/OFF pin can be hard wired directly to
Vin(-) to enable automatic power up of the converter
without the need of an external control signal.
The ON/OFF pin is internally pulled up to 5 V
The converter?s output overvoltage protection (OVP)
senses the voltage across Vout(+) and Vout(-), and
not across the sense lines, so the resistance (and
resulting voltage drop) between the output pins of
the converter and the load should be minimized to
prevent unwanted triggering of the OVP.
When utilizing the remote sense feature, care must
be taken not to exceed the maximum allowable
output power capability of the converter, which is
equal to the product of the nominal output voltage
and the allowable output current for the given
conditions.
through a resistor.
A properly de-bounced
When using remote sense, the output voltage at the
mechanical switch, open-collector transistor, or FET
can be used to drive the input of the ON/OFF pin.
The device must be capable of sinking up to 0.2 mA
at a low level voltage of ? 0.8 V. An external voltage
source (±20 V maximum) may be connected directly
converter can be increased by as much as 10%
above the nominal rating in order to maintain the
required voltage across the load. Therefore, the
designer must, if necessary, decrease the maximum
current (originally obtained from the derating curves)
ZD-01723 Rev 1.2, 04-Jan-10
www.power-one.com
Page 5 of 13
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SQE48T50012-NDA0 DC/DC EIGHTH BRICK
SQL48T20033-NDA0G CONV DC-DC 3.3V 20A 1/8 BRICK
SQM48S20033-NS00 DC/DC EIGHTH BRICK
SQM48T20010-PCB0 DC/DC EIGHTH BRICK
SRBA-03A1A0G CONV DC/DC .75-5V ADJ 3A SMD
SRBA-03E1A0G CONV DC/DC 3A .75-5.0V SMD
SRBA-06A2A0G CONV DC/DC .75-5.5V ADJ 6A SMD
SRBA-06F2A0G CONV DC/DC .75-3.63VDC 6A OUTPUT
相关代理商/技术参数
SQE48T40025-NDA0G 功能描述:DC/DC转换器 100W 2.5Vout 40A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
SQE48T40025-NDAK 制造商:Power-One 功能描述:
SQE48T40025-NDAKG 制造商:Power-One 功能描述:Module DC-DC 1-OUT 2.5V 40A 8-Pin 1/8-Brick 制造商:Power-One 功能描述:DC-DC CONVERTER,48V,THRU-HOLE,40ADC,2.5V,NEGATIVE,BULK,HAZMA - Bulk
SQE48T50012-NDA0 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
SQE48T50012-NDA0G 功能描述:DC/DC转换器 1.2Vout 50A 1.2Vout 50A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
SQE5-P 制造商:Power-One 功能描述:
SQETHERNET 制造商:Intel 功能描述:
SQF620001 功能描述:OSC 156.25MHZ 3.3V HCSL SMD RoHS:是 类别:晶体和振荡器 >> 振荡器 系列:SaRonix-eCera™ SQ 标准包装:1 系列:VG-4512CA 类型:VCXO 频率:153.6MHz 功能:三态（输出启用） 输出:LVPECL 电源电压:3.3V 频率稳定性:- 工作温度:-40°C ~ 85°C 电流 - 电源（最大）:60mA 额定值:- 安装类型:表面贴装 尺寸/尺寸:0.276" L x 0.197" W（7.00mm x 5.00mm） 高度:0.071"（1.80mm） 封装/外壳:6-SMD，无引线（DFN，LCC） 包装:Digi-Reel® 电流 - 电源（禁用）（最大）:- 其它名称:SER3790DKR